2021 Bluewater Full Aluminum 6x12x6 + V Nose Enclosed Trailer

For sale a 2021 Bluewater 6 feet wide x 12 feet long x 6.2 feet high/tall to the aluminum frame for the roof, Plus the over 2 foot long, V Nose, Full Aluminum Enclosed Trailer With Barn Doors.

It has LED light for tail lights and they are very bright.

There are also two bright lights on the inside if you need to work in the trailer at night.

The side door has a key and it also locks from the inside with a dead bolt.

The aluminum frame is 16 inches apart on center, at the bottom and on the top and sides.

It has four smaller D rings, one in each corner, each rated for 1100 lbs.

It also has two, 2 foot E tracks one on each side of the wall and ten, 2 foot E tracks that were just installed on May 29th, 2023 to complement the three Condor wheel chocks that were also installed on the same date.

Just the E tracks and the three Condor wheel chocks, with all the E track attachments and hardware and the E track adapter plus installation were almost $3000.

The trailer was used to move Styrofoam, fir solar panels installation by the previous owner and it was only used sporadically since he had other trailers also.

I had it set up for moving motorcycle and the reason that I had this Condor wheel chocks installed is because, they are the best on the market, and if you need to use the trailer for other things, they can come off in few minutes without using any tools.

The trailer is in very good condition, except for a few dings and dents, which are very easy to get, from stone chips and such, on aluminum.

-One 2990 lb Spring Axle

-6.2ft Interior Height

-All Cross members are 16" on center

It has a couple of shelves in the front part of the V nose, and a couple of rods on one side for racing suits, or whatever you want to hang on them.

It has a three component plastic store box too, and a cople of coat hanges, one on the back of each door.

It takes a 2 inch ball and it has a 4 prong connector for the wiring.

The trailer is rated for 2990 lbs. fully loaded and it would make a great trailer for the following:

-motorcycles -ATV -side by side -tractor -lawnmowers -moving -snowmobile -etc.

The price is $9000, with all the twelve E tracks that have already been installed.

The price is $10,500 with the three Condor motorcycle wheel chocks and the reteiner for the E tracks so you can position them where it's most convenient for you and your motorcycles.

The inside measurements are as follows:

-11 feet and 9.5 inches long, without the V nose.

-6 foot and 2 inches tall/high up to the roof frame beems.

-5 foot and 9.5 inches wide.

I don't need to sell it but, I will if I get what I am asking for it.

Please don't waste my time with BS.

Call George at Chifor Racing at 519-969-8743.

I might consider trading it for a bigger enclosed aluminum trailer.

Note:

The wheel chock at the back, has a E track adapter, that the wheel chock mounts on top of so it can be easily moved to the E track that is positioned at the back, if you want to transport three sport bikes, two that are facing forward and one that is facing backwards.

The othere two wheel chocks that are in the front, have two, Universal E track adapters, one each so you can easily stager the wheel chock if you need to.

Here is a list of all 5he Condor wheel chocks and different E track adapters that went into this trailer:

-3 Condor Trailer-Only Motorcycle Chock/Lock # SC-2000 $359.99 each plus tax for a total of $1220.37

Specifications:

The CONDOR® SC-2000 Trailer-Only Chock is our all-steel version of our Pit-Stop.

It has all the same capabilities except it is designed for trailer use only.

Our patented adjustable cradle fits all bikes from dirt bikes and sport bikes, to cruisers and heavy touring bikes, and anything in between, up to 3,000 lbs.

It will work on front and rear tires from 14" to 22" and 80mm to 230mm.

The patented locking mechanism safely and securely supports your motorcycle in an upright position on all transportation platforms.

Our chock will hold your motorcycle so securely, only one person is needed to load and unload any bike, and only two tie-down straps are usually required.

And you won't damage your sensitive suspension parts because you never need to over-tighten your tie-down straps.

The Trailer-Only chock attaches and detaches to your trailer in seconds with four thumb screws.

You will be amazed at how secure and safe your ride will be once tied down in the CONDOR® wheel chock.

The SC-2000 comes complete with all brackets and hardware to mount this unit to your trailer.

The CONDOR® SC-2000 folds down for easy storage and weighs only 26+ lbs. Its dimensions in the upright position are 9” wide, 25” long and 15” high.

Once folded, it becomes 9” wide, 25” long and 7” high.

If you don't require the free-standing versatility of the Pit-Stop, the Trailer-Only model is the way to go.

This is also the perfect wheel chock to attach to your lift table to keep any bike stable while working on it, and it can also extend your lift table by 10".

-2 Condor Universal E-Track Adapter Kit for Condor products # UNIV-ETRACK $245.99 each plus tax=$555.94

Specifications:

The Universal E-Track Adaptor Kit (UNIV-E TRACK) is designed to be used with either a Condor Pit-Stop/Trailer-Stop, (PS-1500) the CONDOR Trailer-Only model (SC-2000), the CONDOR Scooter Chock (SCC-4000) and the Condor Chopper Chock (CHCK-1500).

The kit allows our chocks to quickly and securely attach to the E-Track on any trailer platform, whether the E-Track is above the floor, recessed, or flush-mounted.

Now you can adjust the position of the chock anywhere along the E-Track for maximum flexibility in positioning a motorcycle, and the chock can be adjusted side to side between the E-Track.

The minimum and maximum center-to-center distances between the mounted E-tracks are 26” and 46” respectively.

Keep in mind that if you are using our PS-1500 the minimum distance between the inside of the tracks is limited by the width of the PS-1500 which is 29”.

The Universal E-Track Adaptor Kit comes will all the necessary hardware for assembly, including a Boomerang Bar for added stability to your CONDOR Chock.

Also available is our new A-Track Adaptor Kit (A-TRACK KIT), sold separately. The A-Track Adaptor Kit contains all the necessary hardware to adapt our Universal E-Track Adaptor Kit for use with your floor-mounted A-Track. It will allow you to use any Condor Wheel Chocks.

-1 Condor E-Track Adapter for Condor products # E-TRACKADAPTOR $224.99 plus tax=$254.24

Specifications:

Our E-Track Adapter allows you to mount the SC-2000 Trailer-Only Model on your existing E-Track, to give you more flexibility in placing your motorcycle in your trailer or transport platform.

Can be used only with above-floor, or flush-mounted E-Track.

Will not work with recessed E-Track.

-2 Condor Boomerang Bar # CHCK-BMBAR $74.95 plus tax each=$169.30

Specifications:

Our Boomerang Bar is designed to add extra stability to the PS-1500 Pit-Stop, if necessary, because of an extended front fork or other special circumstances. Many original equipment manufacturers, like Harley-Davidson, Indian, Victory, Yamaha, Kawasaki and others, have used a boomerang bar on the Pit Stops that they place their motorcycles on at many shows where people can get on and off their bikes.

Simply attach the Boomerang Bar to the existing holes located at the rear of your PS-1500 (legs facing Back).

The bar is made from high quality steel with a nonskid pad.

-1 Condor Garage Dolly Trailer Kit # GD-TK3000 $49.95 plus tax =$56.44

Specifications:

CONDOR®’s Garage Dolly is now even more versatile! We’ve developed a Trailer Adapter Kit (Part# GD-TK-3000) so you can now use the Dolly to transport your motorcycle in a trailer.

The kit contains two separate brackets that mount permanently to the floor of your trailer, one for the front of the Dolly, and another one for the rear of the Dolly.

Once installed, simply attach the Garage Dolly to the Trailer Adapter Kit brackets, and ride or roll your bike into the Dolly.

First, secure the motorcycle to the Dolly, and then use your tie-down straps to secure the Dolly to the trailer.

Now you’re ready to transport your motorcycle safely and securely, just as you do with the Pit Stop Wheel Chock, the Trailer-Only model, or Chopper Chock.

-12, 2,000-lb E-Track, Horizontal, 24-in black $20 each plus tax =$271.20

Features:

E-Track Cargo Management Track is the foundation of the E-Track System for versatile mounting points anywhere.

Creates multiple versatile tie-down points where you need them to help secure loads.

Install to walls or flooring of your trailer, truck, garage or shed.

E-Track guides accept any E-Track accessory (sold separately).

Break strength of 2000 lbs (907 kg).

Safe work load of 667 lbs (303 kg).

Easy install with 1/4" diameter mounting holes (hardware not included).

Length: 24" (61 cm).

-100 E-Track Metal Screw Set at $15 plus tax,for a 20 piece set=$84.75.

A complete set of zinc-plated screws for fastening E-Tracks to metal surfaces.

Feature(s):

Zinc-plated finish for corrosion and rust resistance.

Self-drilling screws easily created their own hole through the metal.

No drilling required.

Application(s):

Use to mount E-Tracks to most metal surfaces.

Attributes and Specifications

SKU 8695165

Package (L x W x H) 0.8 x 4 x 6 in.

Weight 0.4 lbs

Colour/Finish Zinc plated

Sub Brand Snap-Loc

Safe Working Load (lb) 333

Item Name E-Track Metal Screw Set

Breaking Strength (lb) 1,000

Type 20 pc self-driller screws

Packaging (qty) 20

Size (in.) 1/4 x 1-1/4

-8 hours labour, for instalation of the E-TrackSystem and Condorwheelchocksandthe differentE-Trackadapters, @ $120/hour plus tax=$1084.80.

I am sure that I am still forgetting something but this is the just of it.