Jeep YJ 1987 ( MORE INFO )

More information has been added as to what needs to be done to finish and more of what has been done. 6 Cylinder Standard 5 speed Because everyone wanted to know what has been installed into this .............this..........Beast. I have put up a list below of what has been done by me and the previous owner. 1987 Jeep Wrangler Larado 2dr. came with listed Items. Never driven since project started. ............................................................................................................................................ New fiberglass body replacement, tub, fenders and hood. from Shell Valley Classic Wheels Inc. New steel windshield frame and windshield glass, from Jeep New neoprene body mount kit, from Wheels Performance New spring bushings, neoprene, from Wheels Performance New heavy duty front and rear 2 inch lift off road spring shackles New Webber carb, from NAPA New fox header, from NAPA New LED tail lights, From NAPA New LED off road lights ( windshield mounted top light bar and two side mounted spots ) New cylinder head, from NAPA ( installed professionally by garage ) New Complete engine gasket set , from NAPA New wiring harness, not very good and partially installed ( replaced with another ) New rad in box ( now installed ) from NAPA New electric fan ( now installed ) from NAPA New cab heater , ( aux unit and kind of small ) from NAPA New starter relay, from NAPA New plugs and wires, stock from NAPA New clutch, from NAPA New shifter boots, OEM Jeep New front rotors and pads, from NAPA New rear brake shoes and turned drums, from NAPA New rear wheel cylinders, from NAPA New e-brake cables, from Jeep New e-brake foot pedal assembly, for a glass body. from classic wheels New gas, clutch and brake pedal assembly, OEM Jeep Frame professionally repaired then covered with POR15 Full factory hard doors Factory half hard doors, ( now on body ) Soft top frame for half doors, not complete Factory roll bar and front seats with brackets.( installed ) New seat belts for front seats Jeep came with all new fuel lines installed and well as all new brake lines installed, including all the flex lines. The transmission and transfer case have all been gone through, as well as both front and rear differentials. New upper and lower ball joints, and tie rod ends as well as all neoprene bushings. In the springs and panard bars.

NOW STARTS AND RUNS, with these added parts ............................................................................................................................................

New dash to replace the fiberglass one that was installed wrong ( upside down ) New switch panel for dash, with !2v outlet and volt meter. New HEI distributor New Excel wires New wiring harness, mostly installed ( painless type system ) New rad and heater hoses, from NAPA New valve cover vent, from APC New fuel filter, from NAPA New gas cap, from Car Quest New oem upper and lower shifter boots, from Jeep Used set of 33 inch tires ( 5 matching like new tires ) Used set of wide aluminum rims, ( 4 aluminum and 1 steel spare ) New wheel nuts, from tire shop New 160 amp alternator, from Starter Alternator shop OPIMA battery Used soft top frame parts to install top New GPS speedo New aftermarket gauges with a GPS speedo Starter rebuilt, by Simcoe Starter New rubber seal kit ( doors and such ), from Rock Auto New factory heater hose ( both ), from NAPA New upper and lower rad hose, from NAPA New radio, (needs to be hooked up and speakers ), from Audio Ave New headlight switch, from Car Quest Header wrap for collector, from APC New heat shield for intake, from NAPA Fresh oil and filter, from NAPA Complete YJ for parts, has hard top, good doors and front clip. Runs frame and body tub shot shot. WHAT IS NEEDED TO FINISH: really not much. Wiring under the dash hooked up to gages and switches. Not that big a deal all wires are marked and just need to be soldered together and heat shrink tubed. Door latches installed on either side, the exhaust needs to be finished, spare tire mounted to the back or inside, back seat installed if needed, the seat belts installed and the heater installed. Should flush out the brake lines and clean all the brake surfaces as its been sitting for a number of years, before I got it. They all work just fine, its just what I would do. A front end alinement would also be a good idea as I don't think it has been done since all the new parts installed.

.................................................................................................................

I have a complete YJ for parts, has hardtop good doors and front clip. Runs frame and body shot. 14 grand has been invested into this project looking for $10750 for everything that includes a running parts jeep. Last photo is of it when I bought it. Located in Norfolk 30 min South of Brantford. The reason for selling is my health.