DawnRay 4 inch gimbal LED Recessed Light 9 W white

Visit us
9390 Woodbine Ave #1tmp, Markham, ON L6C 0M5, Canada(View Map)
  • Condition


    We provide bulk orders for our products. Whether you're a contractor, electrician or builder, we want to be your supplier of quality products at competitive prices. We believe in customer satisfaction! We provide fast shipping and also have the best customer service in the industry! Please feel free to contact us at 647-350-8898 if you need any assistance with the price.




    90° Tilting

    High Performance

    Easy Installation

    5CCT Switchable

    10%-100% dimming capability

    5 Years Warranty

    Specs Sheet

    Cut-Size: 4-1/4″

    Wattage: 9W

    Input: 100-120V AC, 60Hz, 0.09A

    Beam Angle: 38°

    Lumens: 860LM

    CRI: 80+

    5 CCT: 2700K/3000K/3500K/4000K/5000K

    Power Factor: 0.98

    Light Source Life (hrs): 50,000

    Type IC: Yes

    Airtight: Yes

    Damp Location: Yes

    Wet Location: No

    LED Gimbal Slim Light Installation Guide

    Important: Read all instructions before installing fixtures. Retain for future reference.
    Operation Temperature:
    Suitable for damp locations.
    Suitable for the insulated ceiling.
    Type IC Rated for direct contact with insulation

    Safety: For your safety, this fixture must be wired in accordance with local electrical codes and ordinances. All work should be done by a qualified electrician.

    Warning: Make sure power is OFF from the electrical panel before starting the installation or attempting any maintenance. For indoor installation only.

    Tools Required:
    *Measuring Tape
    *Electrical Wiring
    (use type and gauge suitable for application to connect the fixtures).

    Hole Cut Size:
    4" Round:∅4 1/4"(108mm)

    Assembly Instructions:
    1. Risk of electric shock - turn off the power before inspection, installation or removal.
    2. Locate a suitable position to place the LED fixture and open a hole in accordance to the cut-hole dimensions (refer to Hole Cut Table for appropriate size).
    3. Run the electrical wire from the switch (power supply), through the mounting hole-use NMD90 or BX cable.
    4. Open the hardwire box swing cover and remove the appropriate knockout(s).
    5. Insert the electrical supply cable through the knockout.
    6.Wire box using supplied quick connect push-in terminals. Connect green ground wire of the cable to yellow-green wire of box. Connect white wire of the cable to white wire of box. Connect black wire of the cable to black wire of box.
    7. Place all wiring and connections back into the box and close the cover.
    8.New construction applications: junction box shall be firmly secured to studs, joists, or similar fixed structural units.
    9. Remodel applications: Do not require the junction box to be firmly secured after the mounting plates, studs, joists, or structural units that have been concealed. Snap off the junction box tabs, then insert into the ceiling.
    10. Push spring-loaded clips on the fixture upwards and insert fixture base into the mounting hole. Release the clips and fixture will be pulled flush to the ceiling.
    11. Once assembly is complete, turn on the power to confirm the fixture is working properly.

    Additional Options

    The following services are also made available by this seller. Please reach out to them for more info as there may be additional costs.
    • Willing to ship the item
    • Offers curbside pick up
    • Willing to drop-off / deliver
    • Offers cashless payment
    • Cash accepted
    Kijiji User
    9390 Woodbine Ave #1tmp, Markham, ON L6C 0M5, Canada
    View other listings
    View on website(opens in a new tab)
    avg reply
    reply rate
    on Kijiji

    More from NVC International Inc

    View all
    Take steps to make your Kijiji transactions as secure as possible by following our suggested safety tips. Read our Safety Tips